Roku setup

[jadkins]

Followed instructions to set up my new Roku player. Powered up, and I don't get a set up screen. Disconnected and reconnected, still no screen. Only get a blinking blue light on unit.

[Strega2]

Is it plugged into the wall?  (Sometimes people plug them into a TV USB port and some of those don’t supply enough power.)

Is the TV set to the correct input?

[jadkins]

yes and yes

[jadkins]

To expand on my last reply. My TV recognizes my device, but still no picture.

[RokuJohnB · Accepted solution]

Hi @jadkins,

Thanks for keeping us posted, and welcome to the Roku Community!

We understand you're having trouble with the Roku device because you can't see any pictures. We're happy to help.

Make sure your Roku player is connected directly to the TV. If it is connected to an audio/video receiver (AVR) or soundbar, first disconnect it and connect it directly to the TV. This will remove any issue with the AVR or soundbar and make it easier to troubleshoot the problem.

First, turn on the TV and press a button on the Roku remote control to ensure that the Roku device is not in standby or screensaver mode.

These are the most common reasons you may not see the picture on your TV:

1. You have the wrong input (source) selected on your TV
   • This is extremely common and an easy mistake to make. Most TVs have several video inputs on the back or side of the TV that are used for connecting different devices, such as a cable box, gaming console, and, of course, a Roku player. You must select the input (sometimes referred to as source) that matches the one to which you have the Roku player connected.
     • Look to see which input you have the Roku player connected to. The video connector will be labeled with the input name, e.g., HDMI 1, HDMI 2, AUX, VIDEO IN 1, etc.
   • The way you change inputs can differ based on the TV brand and model, but it is usually accessible from a button on the remote control. If you can, check the instructions that came with your television, or try the following:
     • Look for a button on your TV remote control that says Input, Source, AUX, Video, TV/Video, or something similar. Press this button. Depending on your TV, pressing the button may cycle through available inputs or display a menu with a choice of inputs.
     • If it cycles through the inputs - wait 10 seconds between button presses to allow the TV to detect the video.
     • If a menu is displayed - use the arrow buttons on the TV remote to choose the correct input and press Enter or Select. Alternatively, select each input one at a time. Wait 10 seconds between each to allow the TV to detect the video.
     • In both cases, if no video is detected on the input, the TV will usually show a message such as "No video" or "No signal detected."
2. The video cable is not connected correctly, or the cable is faulty
   • Check that the video cable is firmly connected to the back of your Roku player and the HDMI or composite connector on the TV. If you have a Roku Streaming Stick, ensure it is firmly connected to the HDMI connector on your TV.
   • If you can, check to see if you have a faulty cable by connecting your Roku player with a different cable.
3. There is a problem with the TV.
   • If you can, try connecting the Roku player to a different input on the TV to see if the problem is with the TV's connector.
   • If you can, try connecting the Roku player to a different television to see if the problem is with your Roku player or the TV.
4. Enable CEC or turn off auto power savings.
   • If you do not see a picture after pressing a button on your Roku remote, it is possible that your player cannot "wake up" your TV over the HDMI connection. To fix this, make sure that HDMI-CEC is enabled on your TV. You can turn off auto power savings if you prefer that your player never enter low power mode.
5. There is a problem with the USB power adaptor, or the adaptor does not meet the requirements.
   • Your Roku player may not receive enough power, even if the power light is on. This happens sometimes if you connect your Roku player through a third-party device with a USB/AC power adaptor that does not meet more recent USB standards. Try a different power adaptor, or plug your Roku player directly into a power source. For more information, learn what to do if the red light is flashing or you see a "low-power" warning.
6. If all else fails…
   • Disconnect and reconnect all cables, including the power cable.

We would recommend trying to see if that resolves your issue. Please keep us posted.

Best regards,
John